Showing 5 results for Colloidal
N. Hamedani Golshan,, H. Sarpoolaky, A. R. Souri,
Volume 8, Issue 1 (3-2011)
Abstract
Abstract: Efforts have been carried out in order to use microsilica to develop a forsterite bond rather than other types of binders in the basic refractory castables. According to the higher drying rate and sinterability of colloidal silica, it has been proposed in the recent years. In the present work, effects of replacement of microsilica by colloidal silica evolution of forsterite bond have been studied in magnesia based refractory castables. In this way, Physical properties of prepared samples with different amount of colloidal silica versus temperature were investigated. In addition, phase variation and microstructural evolution of sintered specimens at 1000, 1200 and 1400 °C were studied by X-ray diffraction (XRD) and scanning electron microscope (SEM) respectively. Results showed that, due to Reaction of magnesia with microsilica and colloidal silica, magnesium hydrate and magnesium silicate hydrate formed in the dried samples strengthening the texture of the samples while forsterite formed from about 1000 °C and gradually increased with temperature rise. Also, better forsterite formation would be appeared by increasing the colloidal silica content. Further investigation carried out on the type of silica addition on properties of the castable refractory samples. It was found that the presence of micro silica and colloidal silica simultaneously (MS3C3 sample) at 1400 °C, caused modifying mechanical strength in compare with sample with only micro silica (MS sample).
H. Yaghoubi, H. Sarpoolaky, F. Golestanifard, A. Souri,
Volume 9, Issue 2 (6-2012)
Abstract
Colloidal silica bonded refractory castables have been developed recently. It was found that colloidal silica is one of the best binders can substitute other binders such as cement in No Cement Castable (NCC) and Ultra Low Cement Castable (ULCC) refractories. Also composition of colloidal silica with appropriate additives resulted in a gel form which makes the initial strength. Moreover, the nano size silica particles are extremely reactive in high alumina castables and may encourage the mullite formation in the microstructure. In the current study, four castables were prepared. The sample containing 6wt % microsilica was a reference, then microsilica was replaced by different amount of colloidal silica (2.5, 5, 7.5 wt %). Silica and water content was kept constant. It’s concluded that the castables containing the optimum amount of silica sol shows remarkable increase in both castable fluidity and mechanical strength (CCS and MOR) in dried and sintered state. It was also found that nanosilica particles increase the rate of needle-shaped mullite formation during sintering at 1400°C. According to FTIR results, the addition of Calcium Aluminate Cement (CAC) to the silica sol may be responsible for the increment of siloxane bridges (Si-O-Si).
V. Tajer-Kajinebaf, H. Sarpoolaky, T. Mohammadi,
Volume 10, Issue 1 (3-2013)
Abstract
Abstract:Nanostructured titania was synthesized by colloidal and polymeric sol-gel routes. Stable colloidal and polymeric titania sols were prepared by adjusting the proper values of the acid/alkoxide and the water/alkoxide molar ratios. The properties of sols were determined by dynamic light scattering technique and synthesized titania was characterized by thermogravimetry and differential thermal analysis, X-ray diffraction, Fourier transform infrared spectroscopy, optical microscopy and field emission scanning electron microscopy. The results showed particle size distribution of colloidal sol 10-50 nm compared to polymeric one which was 0.5-2 nm. Phase analysis of the colloidal sample revealed anatase as the major phase up to 550 °C, while the polymeric route resulted only anatase phase up to 750 °C. On the basis of results, titania prepared by the polymeric route showed better thermal stability against phase transformation than the sample prepared by the colloidal route. Also, microstructural studies showed that titania nanopowder can be produced by both sol-gel routes
Azam Bayat,
Volume 21, Issue 0 (3-2024)
Abstract
The lindgrenite compounds [Cu3(MoO4)2(OH)2] with various architectures and high crystallinity were prepared by a simple surfactant-assisted hydrothermal method. Then, the Cu3Mo2O9 samples were prepared by calcination of the as-synthesized Cu3(MoO4)2(OH)2. The resulting samples had high crystallinity, colloidal properties, high-yield, large-scale production capability with using of nontoxic and inexpensive reagents and water as an environmentally solvent. The scanning electron microscope studies showed that the as-prepared lindgrenite nanostructures were well crystallized with rod, sheet and hollow sphere morphologies. These products were content of the Cu3(MoO4)2(OH)2 rods with diameters of about 100 nm, the Cu3(MoO4)2(OH)2 nanosheets with thickness of 30–100 nm and the Cu3(MoO4)2(OH)2 hallow spheres, consisting of a large number of nanosheets with thickness of about 40-70 nm. The Cu3Mo2O9 samples that obtained by thermal treatment of lindgrenite retained the original morphologies. Meanwhile, the photoluminescence and magnetic properties of the nanosheet samples showed super paramagnetic behavior at room temperature and in comparison with previous works, Cu3(MoO4)2(OH)2 and Cu3Mo2O9 samples synthesized by the surfactant-assisted hydrothermal method had a very obvious red-shifted PL emission and high intensity.
Amin Rahiminejad, Mojgan Heydari, Fariba Tajabadi,
Volume 22, Issue 1 (3-2025)
Abstract
Targeted drug delivery systems have been developed to overcome the disadvantages of conventional drug delivery systems and folate is one of the targeting molecules that has received attention in recent years. The attachment of this molecule to the surface of niosomal carriers has been achieved using Castor oil as an intermediate molecule. We synthesized caster folate (CF) and incorporate to noisome structure as biocompatible component for targeted delivery of anticancer drug Doxorubicin. This research studies the novelty of castor folate ester in the scope of niosome-based drug delivery systems. The aim was to investigate the feasibility of manufacturing and evaluating a niosomal carrier containing the drug doxorubicin hydrochloride (DOX) and its targeting by the combination of CF. The results of Fourier Transform Infrared Spectroscopy (FTIR) confirm chemical bounding between folic acid and castor oil. SEM showed good morphology with spherical structure of niosomes. These niosomes have particles size of 330 to 538 nm for different samples. Also, zeta potential was -28 to -40 mV that results good stability. The addition of CF to niosomal samples increased wettability and drug loading efficacy and along with DLS and zeta potential results confirms the folate impact on surface hydrophilicity of niosome spheres. The prepared formulations increased the effectiveness of doxorubicin on L929 fibroblast cells. The proposed biocompatible component showed the role of CF in the architectural integrity of niosomal lipid bilayers.
